Stool

A small wooden stool will be used in every home. With these chairs with great joy, children rush. Sitting on such a stool is convenient to clean the potatoes and perform other "sedentary" work. However, not many people decide to buy a small stool due to the fact that there is always a more important waste of funds. And here, to make a small wooden stool with your own hands the power of almost everyone. To make it you will need a jigsaw and a little imagination. Preparation. Layout of the board. Parts manufacturing, polishing. Assembling the stool. Painting. Preparation. Preparation of material and necessary tools plays an important role and saves time in the future. For the manufacture of the stool, we need: - a weathered board with a size of 800x200x25 mm (dimensions approximate, we can proceed from what is available), - 8 shiny screws (50-60 mm), - emery paper , - jigsaw, - screwdriver or screwdriver, - paint and varnish on wood, - tape measure, pencil and corner. Board marking. You need to start with the layout of the board.First of all, with the help of a corner, a pencil and a tape measure, we mark a rectangular piece without knots 32-33 cm long. This will be the upper part of our high chair. Next, note two segments of 23 cm - it will be sideways. Now it is desirable to give them some figured pattern. You can use any objects that have a circle for this purpose, simply by drawing them with a pencil. But, this method involves the irrational expenditure of time. After all, it is necessary to mark the center and other dimensions in each edge. Therefore, for the sides, it is better to use a pattern, cut out previously from thick cardboard or other material. It will allow you to quickly and easily mark a large number of sides. It is enough to attach a pattern and circle a pencil.
 Whiteboard Layout
By the way, using the figured pattern on the side not only gives them a beautiful look, but also allows you to cut all unwanted knots.And immediately mark the jumper. It should be trapezoidal and have sides of 230 and 220 mm. The width of the jumper is not critical - from 80 to 120 mm.  Manufacturing details
So,has a marked up board.
Manufacturing of parts
Important! Do not draw too thick lines - it affects the evenness of the trim. Yes, and erased pencil is not so easy. Manufacturing of parts. With the help of jigsaw we cut out all our parts. Here evenness is important. For even trimming of the cut, the tool canvas is better not to follow along the line, but to the side of it.
 Manufacturing of parts
You can learn how to cut evenly with unnecessary waste. So, cut out all the details.
 details of the stool
Next, use a large sandpaper to smooth the sharp corners of the parts around the entire circumference, grind the ends.
skins parts
This will give the product not only a beautiful look, but also hide all the possible irregularities of the cut. Next, all these details are carefully polished with fine emery paper. It is most rational to carry out this procedure at this stage, as there may be a number of inconveniences when grinding the finished structure.It is convenient to grind even planes, having put sandpaper on a wooden block, or on a manual grinder for puttying. The main thing is the quality, because after painting all the defects appear and will be visible. This is how the polished and unpolished flanges look.
 cover
So, it has the same details, but already ready to build.
Assembling the stool
Assembling the stool. It is desirable to carry out the assembly in this order: - connect the sides with jumper (1 screw on each side); - high we place this construction on a flat surface and fasten the top cover (2 screws on each side); - Strengthen the connection of the side panels with the jumper (another 1 screw).
 Build the stool

Stool assembled! Check it again on a flat surface. In case the stool staggers a bit, then we prick the legs until the product is completely stable.
 Build the stool
Paint. Before painting more once we check the product for defects, if necessary, erase them and the remnants of a pencil.Using a brush, we clean the stool of wood dust and proceed to painting. There is already "no friend to the taste and color"! You can leave the natural color of the tree, revealing its colorless varnish. You can give the product a certain color with a variety of colors on wood, which is full in all hardware stores. In principle, one layer is enough for painting. But, if, after complete drying of the first layer, the surfaces are slightly sanded again with fine sandpaper and a new coat of varnish is applied, the shine of the product will noticeably increase. Important! Poorly polished ends absorb more paint and become darker.
 Stool
This is how a ready, varnished chair looks.

Related News:


Paper Transformer Star
French cuisine: frog legs
Repair the room with photo wallpaper
A simple homemade blacksmith
Quality and style of vinyl wallpaper
Soft toy
Light Meatballs with Filling and Delicious Sauce